M174994 Deck Belt for John Deere X330 X350 X354 X370 42-Inch Deck
M174994 Deck Belt for John Deere X330 X350 X354 X370 42-Inch Deck
Overview
This aftermarket M174994 mower deck belt fits select John Deere X330, X350, X354, and X370 lawn tractors equipped with compatible 42-inch mower decks.
The supplier lists this aramid replacement belt at approximately 1/2 inch wide by 144.8 inches long.
Use this listing when your original mower-deck belt number is M174994 and the installed deck uses the same belt dimensions, pulley routing, and tension-system configuration.
Important: Match the original belt number and installed mower deck before ordering. Do not select this belt using the tractor model or 42-inch deck width alone.
Key Features
- Aftermarket mower-deck drive belt
- Replacement Number: M174994
- Supplier Reference: AB632-AA
- Supplier-Listed Width: Approximately 1/2 inch
- Supplier-Listed Length: Approximately 144.8 inches
- Belt Material: Aramid
- Color: Gray
- Quantity Included: One belt
- Designed for select John Deere 42-inch mower-deck applications
Replaces These Belt Numbers
- M174994
Supplier Reference Number
- AB632-AA
Search-Friendly Number Formats
- M174994
- 174994
- AB632-AA
- AB632AA
Belt Specifications
- Component: Mower-deck drive belt
- Supplier-Listed Width: Approximately 1/2 inch
- Supplier-Listed Length: Approximately 144.8 inches
- Material: Aramid
- Color: Gray
- Quantity: One belt
Belt measurements can vary slightly depending on how the belt is positioned or measured. Use the original M174994 part number as the primary fitment check.
Compatible John Deere Models
The supplier lists this M174994 belt for select 42-inch mower-deck configurations on the following John Deere lawn tractors:
- John Deere X330
- John Deere X350
- John Deere X354
- John Deere X370
Fitment note: These are supplier-provided model examples. Confirm that the original mower-deck belt is marked M174994 and that the installed deck uses the same routing and tension configuration.
John Deere X330 Fitment Note
The supplier lists the M174994 belt for select John Deere X330 tractors with compatible 42-inch mower decks.
The X330 can be equipped with more than one mower-deck configuration. Confirm the original M174994 belt number before ordering.
John Deere X350 Fitment Note
The supplier lists the M174994 belt for select John Deere X350 tractors equipped with compatible 42-inch mower decks.
Do not order this belt for an X350 using the tractor model alone. Match the original belt number and mower-deck routing.
John Deere X354 Fitment Note
The supplier lists the M174994 belt for select John Deere X354 tractors with compatible 42-inch mower decks.
Confirm the original belt number, deck configuration, idler layout, and pulley routing before installation.
John Deere X370 Fitment Note
The supplier lists the M174994 belt for select John Deere X370 tractors equipped with compatible 42-inch mower decks.
The X370 may be used with different mower attachments or deck configurations. Confirm that the required mower-deck belt is M174994.
Mower Deck Belt Position
The M174994 is used in the mower-deck drive system. It transfers power through the deck pulley system to operate the mower blades.
This belt should not be confused with:
- The tractor traction-drive belt that moves the mower
- A snowblower or other attachment belt
- A belt used on a different mower-deck size
- A primary or secondary belt from a separate two-belt deck system
Trace the original belt routing before removal and confirm the M174994 number before ordering.
Before Ordering
Confirm all of the following before ordering:
- The original mower-deck belt number is M174994.
- The mower is a compatible John Deere X330, X350, X354, or X370.
- The installed mower deck is a compatible 42-inch configuration.
- The supplier-listed size of approximately 1/2 inch by 144.8 inches matches the required belt path.
- The replacement is for the mower-deck drive system.
- The belt is not being confused with the tractor traction-drive belt.
- The spindle pulleys, idler pulleys, tension arm, spring, and belt guides match the original configuration.
- The original belt routing has been photographed or recorded before removal.
Do not install the replacement until the part number, deck configuration, dimensions, and routing have been confirmed.
Common Symptoms of a Worn Deck Belt
- Mower blades turn slowly under cutting load
- Belt squeals when the PTO clutch engages
- Belt repeatedly jumps off a spindle or idler pulley
- Visible cracking, fraying, glazing, or burned belt surfaces
- Loose belt tension with the tension system engaged
- Reduced grass-discharge or bagging performance
- Burning-rubber smell near the mower deck
- PTO clutch engages but the mower blades do not turn
- Uneven blade speed or inconsistent cutting performance
Installation Notes
- Park the mower on a level surface and remove the ignition key.
- Disconnect the spark-plug leads before working near the mower deck.
- Photograph or sketch the original belt routing before removal.
- Inspect all spindle and idler pulleys for bearing wear or damage.
- Inspect the tension arm, tension spring, and belt guides.
- Replace seized pulleys or damaged tension components before installing the new belt.
- Confirm the belt is seated completely inside each pulley groove.
- Check that the flat and V-shaped sides of the belt contact the correct pulleys.
- Rotate the mower-deck pulley system manually before starting the engine.
Quick Ship Fulfillment
This item may ship directly from one of our trusted U.S. distribution partners to help reduce transit time. Packaging, labeling, or warehouse origin may vary, but the part will match the replacement number, fitment notes, and supplier specifications shown in this listing.
Why Buy From PTO Direct USA
- Part-number-first listings to help reduce fitment mistakes
- Focused mower-deck and PTO replacement parts
- Clear replacement numbers and model-fitment notes
- Practical support when you need help checking compatibility
FAQ
What does the M174994 belt fit?
The supplier lists M174994 for select John Deere X330, X350, X354, and X370 tractors equipped with compatible 42-inch mower decks.
How long is the supplier-listed M174994 belt?
The supplier lists the belt at approximately 144.8 inches long.
How wide is the supplier-listed M174994 belt?
The supplier lists the belt at approximately 1/2 inch wide.
What material is the M174994 belt made from?
The supplier describes this replacement as an aramid mower-deck belt.
How many belts are included?
This listing includes one M174994 deck belt.
Does M174994 fit the John Deere X330?
The supplier lists the belt for select X330 tractors with compatible 42-inch mower decks. Confirm the original M174994 number before ordering.
Does M174994 fit the John Deere X350?
The supplier lists select X350 42-inch mower-deck applications. Match the original belt number and deck routing.
Does M174994 fit the John Deere X354?
The supplier lists select X354 tractors with compatible 42-inch mower decks. Confirm the original M174994 number.
Does M174994 fit the John Deere X370?
The supplier lists select X370 tractors with compatible 42-inch mower decks. Match the installed deck and original belt number.
Does M174994 fit every 42-inch John Deere deck?
No. John Deere produced many different 42-inch mower-deck configurations. Match the original belt number, deck layout, dimensions, and pulley routing.
Is this the tractor traction-drive belt?
No. This listing is for a mower-deck drive belt. The traction-drive belt that moves the tractor is a separate part.
Can I order this belt using only the tractor model?
No. Confirm the original M174994 number, installed mower deck, dimensions, and belt routing before ordering.
Related John Deere Parts and Guides
Need a different belt? Browse the full mower deck belts collection.